Olinuxino-Micro first contact

[ecolomato]

Hi all,
I´ve just received an olinuxino-micro board with sd-card from olimex. It´s the first time I use this board (or any iMX233). I´ve inserted the sd-card, connected tv output to a monitor, powered the board with 5V, and nothing happens (the led doesn´t light and the monitor doesn´t show anything).
Also tried comunicating the board via hyperterminal at correct baud rate, with correct cable-adapter. The expected message was a login request, but the board reports the following message every 20 seconds:

with sd card in:    0x8020a01d
with sd card out:   0x8020a014

What am i doing wrong?
Could anyone help me? Please.

Thanks!

[olimex]

this usually means problem with the card

[ecolomato]

Ok,
Then what I should do is make another bootable sd-card, ins´t it?

[olimex]

yes, please try to make new SD card, if still no success I will mail you one new

[ecolomato]

Ok,
The card was just blank.
Now Olinuxino is alive, but I have another problem.
The board seems to auto reboot all the time. It doesn´t ask for login via telnet anytime (doesn´t reach that point).
The messages I get in hyperterminal are as follows (copy and paste):

HTLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLFCecurity Framework initializedlowmem  : 0xc0000000 - 0xc4000
Mount-cache ha
PowerPrep start initialize power...ctor  : 0x
co
    mo

les : 0xbf000
Battery Voltage = 0.68V MB)
Kernel command lin
No battery or bad battery                                       detected!!!.Disaes)   
pid_max: default: 32768 minimum: 301xfde
      .text : 0xc0026000 - 0xc0
bling battery                                   voltage measurements./r/nLLCMay: 0xc0356000 - 0xc0381a00   ( 175 kB)cache hash table entries: 8192 (order: 3,
11 201215:26:EMI_CTRL 0x1C08404init_ddr_mt46v32m10Frac 0x92926192re ver
        RCU-based detection of stalled CPUs is disabled.yt
LLLLLLLFCLJUncompressing Linux... done, booting the kernel.   Verbose stalled-CPUs detection is disabled.vice 80x
Memo
Linux version 2.6.35.3_OLinuXinoR4 (hehopmajieh@hehopmajieh-office) (gcc versionmy device 80x30ay loop... 226.91
Virtual kernel
console [ttyAM0] enabled     
No b
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)etected!!!.
console
regulator: mmc_ssp-1: fast normal> 3575
Memory: 64MB = 64MB total
regulator: mmc_ssp-2: fa
Memory: 57208k/57208k available, 8328k reserved, 0K highmemr-1: fast normalt: 32768 minimum: 301   
regulato
regulator
Virtual kernel memory layout:ork initializedL 0x1C08404ini
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)12ator: vddd: 8
HTL
r
i.MX IRAM pool: 28 KB@0xc48
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)LLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLL
    DMA     : 0xfde00000 - 0xffe00000   (  32 MB)amily 16pmajieh@hehopmajieh-office) (
PowerPrep s
    vmalloc : 0xc4800000 - 0xf0000000   ( 696 MB): power-t
Battery Voltage = 1.43V7.1 20120421 (pr
    lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)                      detected!!i.MX IRAM pool: 2
    modules : 0xbf000000 - 0                           
CPU: Testing write buffer coherency: ok writebackM
Memory: 57208k/5720
Battery
regulator: core version 0.5 zonelists in Zone order, m
NET: Registered protocol family 1616256         detected!!!.Disa:v5T
regulator: vddd: 800 <--> 1575 mV at 1550 mV fast normaland line: noinitrd console=ttyAM0,115200 root=/dev/mmcbl
regulator: vdddbo: 800 <--> 1575 mV fast normal00   ( 896 kB) iMX233-OLinuXino low cost boar
a
regulator: vdda: 1500 <--> 2275 mV at 1750 mV fast normal: -2, 1024 bytes)m10Frac 0x92926192                     
regulator: vddio: 2800 <--> 3575 mV at 3300 mV fast normal, 32768 bytes)x... done, booting the kernel. lowmem  : 0xc
regulator: overall_current: fast normal entries: 4096 (order: 2, 16384 bytes)R
regulator: mxs-duart-1: fast normalgcc version6 MB)rootwr=
Memory: 64M
regulator: mxs-bl-1: fast normal    .i
Memory: 57208k/57208k ava
regulator: mxs-i2c-1: fast normalREEMPT Mon May 21 10:27:52 EEST 2
regulator: mmc_ssp-1: fast normal kernel memory layout:     
   
HTLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLFC0000000 - 0xc4000000   (  64 MB).  Total pages: 16256er: -
console [ttyAM0
PowerPrep start initialize power...xc0000000   (  16 MB)nel command li
Battery Voltage = 1.42VAM0,115200
      .init
No battery or bad battery                                       detected!!!.Disaxfde00
      .text : 0xc0026000 - 0xc033d000   (3164 kB)entries: 256 (order: -2,
bling battery                                   voltage measurements./r/nLLCMayh table entries: 8192 (order: 3, 32768 bytes
Hierarchical RCU implementation.or
11 201215:26:EMI_CTRL 0x1C08404init_ddr_mt46v32m1etection of statocol fa           
             

Security
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177he hash table entries: 512a
    vmalloc : 0xc4800000 - 0xf000
CPU: VIVT data cache, VIVT instruction cache-bl-1: fast normal d
    lowmem  :
regulator
Machine: iMX233-OLinuXino low cost boardable
NET: Registered protocol family 16m
Memory policy: ECC disabled, Data cache writeback 800 <--> 1575 mV at 1550 mV fast normalmal
     
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256 1575 mV fast normal     .text : 0xc0026000 - 0xc033d000   (3164 kB
     
    vmalloc : 0xc4800000 - 0xf0000000   ( 696 MB) normalieh-office) (g
Battery Voltage = 1.43Vnorm
    lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)                                  detected!!!.Dis
    modules : 0xbf000000 - 0xc0000000   (  16 MB)750 mV fast normalnormalat
i.MX
bling battery   
      .init : 0xc0008000 - 0xc0026000   ( 120 kB)s./r/nLLCMay at 3300 mV fast normalLLLLLLLLLLLLLL
      .text : 0xc0026000 - 0xc033d000   (3164 kB)15:26:EMI_CTRL 0x1C08404init_ddr_mt46v32m10Frac 0
      .data : 0xc0356000 - 0xc0381a00   ( 175 kB)ast normalo low cost boa
LLLLLLLFCLJUncompressing
Hierarchical RCU implementation.l.C disabled, Data cache wri
reg
        RCU-based detection of stalled CPUs is disabled.uXinoR4 (hehopmajieh@hehopmajieh-office) (gcc versiontal
        Verbose stalled-CPUs detection is disabled.measurements./r/nLLCMay 
4.7.1 20120421 (prerelea
NR_IRQS:224#11 PREEMPT
Console: colour dummy device 80x30: power-test-1: fast normalit_ddr_
console [ttyAM0] enabled   
         
         
Bu
regulator: core version 0.5r, mobility grouping on.  T
NET: Registered protocol family 16), cr=0005317726192kernel.       
regulator: vddd: 800 <--> 1575 mV at 1550 mV fast normalole=ttyAM0,115200 root=/dev/mmcblk0p2 rw rootwrements./r
regulator: vdddbo: 800 <--> 1575 mV fast normalcost boardinux versi

ait ssp1=mmc0xff
11 2012
regulator: vdda: 1500 <--> 2275 mV at 1750 mV fast normal     
Battery
    DMA     : 0xfde00000 - 0xf
Dentry cach
regulator: vddio: 2800 <--> 3575 mV at 3300 mV fast normale kernel. : 0xc4800000 - 0xf0000000   ( 696 MB)     
Inode
regulator: overall_current: fast                               
      .
regulator: power-test-1: fast normal 0xfde00000 - 0xffe00000   (  32 MB)
regulator: cpufreq-1: fast normalU implementatio
    vmalloc : 0xc
i.MX IRAM pool: 28 KB@0xc4808000d detection of stalled CPUs is d
HTLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLFCrbose stalled-CPUs detecti
Built 1 zonel
    modules : 0xbf000000 - 0xc000
PowerPrep start initialize power...ff100
Console: colour dummy d
     
Battery Voltage = 1.41Vc0026000   ( 120 kB)d l
No battery or bad battery                                       detected!!xc033d000   (3164 kB) : 0xfde00000 - 0xffe                           

 
regulator: vdda: 1500 <--> 2275 mV at 1
Kernel command line: noinitrd console=ttyAM0,115200 root=/dev/mmcblk0p2 rw rootwator: vddio: 2800 <--> 3575 mV at 3300 mV fast normalR_IRQS:224   

      .data
ait ssp1=mmc- 0xc0381a00
PID hash table entries: 256 (order: -2, 1024 bytes)ol: 28 KB
Hierarchical RCU implem
regulator: mxs-du
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)r: mxs-bl-1: fast normalxc033d000
regulator: vdddbo: 800
regu
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)l
regulator: mmc_ssp-1: fast normal27
Battery Voltage =
NR_I
Memory: 64MB = 64MB totalp-2: fast normalevice 80x
Memory: 57208k/57208k available, 8328k reserved, 0K highmemdt normal is disabled. 

Calib
regulator: power-test-1: fa
Virtual kernel memory layout:               
             
Calibrating delay loop... 226.91 BogoMIPS (lpj=1134592) root=/dev/mmcblk0
CPU: ARM926EJ-S [41069265] revision
pid_max: default: 32768 minimum: 301       
No bat
regulator: cpufreq-1:
Security Framework initializedche, VIVT instruction cacheol:
Mount-cache hash table entries: 512     
Machine: iMX233-OLinuXino low
CPU: Testing write buffer coherency: okLLLLLLLLLLL
Memory policy: ECC disabled
regulator: core version 0.5cache hash table ent
PowerP
NET: Registered protocol family 16in Zone order, mobility grouping o
regulator: vddd: 800 <--> 1575 mV at 1550 mV fast normalbad battery                           
Kernel command l
regulator: vdddbo: 800 <--> 1575 mV fast normalcblk0p2 rw rootwMachine: iM
Virtual kernel
   
regulator: mmc_ssp-2: fast normal 0xffff0000 - 0xffff1000   (   4
regulator: charger-1: fast normale entries:
     
    fixmap  :
regulator: power-test-1: fast normal5] revision 5 (ARMv5TEJ), cr=0005317
regulator: cpufreq-1: fast normal00 - 0xffe00000   (  32 MB)7
CPU:
i.MX IRAM pool: 28 KB@0xc4808000n cacherar
    vmalloc : 0xc4800
HTLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLt boardtion of sta     
                         
       
LLLLLLLFCLJUncompressing Linux...HTLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLL core vers
Inode-cache
        Verbose stalled-CPUs detection is disabled.y 160
LLLLLLLLLLLLLLLLLLLLLLLLLFC     
regulator: v
NR_IRQS:
PowerPrep start initialize power... device 80x30emory: 57208k/57208k a
Battery Voltage = 2.06VyAM0] enabledo: 800 <--
No battery or bad battery                                    1134592y layout:                             
             
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256         detected!!!.
con
regulator: mmc_ssp-2: fast normalregulator:
Cal
Kernel command line: noinitrd console=ttyAM0,115200 root=/dev/mmcblk0p2 rw rootwolta
regulator: power-test-1: fast normallt: 32768 minimum: 301: mxs-bl-1: fa
re
ait ssp1=mmcreq-1: fast
PID hash table entries: 256 (order: -2, 1024 bytes)ol: 28 KB@0xc4808000 table entries: 512 mmc_ssp-1:
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)LLLLLLLLLLLLFCting the kernel.dda: 1500
regulator: core vers
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)..ily 16pmajieh@hehopmajieh-office) (
Battery Voltage = 1.42
Memory: 64MB = 64MB totalo battery or bad battery
Memory: 57208k/57208k available, 8328k reserved, 0K highmembo: 800 <--> 1575 mV fast normal2012LLLLLLLLLLLLLLLLLLLLLLL
Virtual kernel memory layout:                             
    lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)hehopmajieh@hehopmajieh-office) (gcc versionrac 0
    modules : 0xbf000000 - 0xc0000000   (  16 MB)mal command line: noinitr
4.7.1 20120421 (prerel
      .init : 0xc0008000 - 0xc0026000   ( 120 kB) 2012regulator: charger-1: fast normal<-->

Linu
      .text : 0xc0026000 - 0xc033d000   (3164 kB) [41069265] revision 5 (ARMv5TE
Calibrating delay loop... 226.91 BogoMIPS (lpj=1134592)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
regulator: vddd: 800 <--> 1575 mV at 1550 mV fast normal
regulator: vdddbo: 800 <--> 1575 mV fast normal
regulator: vdda: 1500 <--> 2275 mV at 1750 mV fast normal
regulator: vddio: 2800 <--> 3575 mV at 3300 mV fast normal
regulator: overall_current: fast normal
regulator: mxs-duart-1: fast normal
regulator: mxs-bl-1: fast normal
regulator: mxs-i2c-1: fast normal
regulator: mmc_ssp-1: fast normal
regulator: mmc_ssp-2: fast normal
regulator: charger-1: fast normal
regulator: power-test-1: fast normal
regulator: cpufreq-1: fast normal
i.MX IRAM pool: 28 KB@0xc4808000
HTLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLLFC
PowerPrep start initialize power...
Battery Voltage = 1.42V

[ecolomato]

To OLIMEX:
Please, send me a new sd-card. I´ve tried several ways with no success!