CSI error mesage on Lime A20

[Croomch]

Hi guys!

I am currently working on getting two ov7670 cameras interfaced to the A20 Lime via the two CSI.
But I am running into some error messages I cannot seem to fix.
These are, when I run the "dmesg" command:

Code Select Expand


[   71.264374] incomplete xfer (0x20)
[   71.270577] Error -70 on register write
[   71.278674] [CSI_ERR]chip found is not an ov7670 chip.
[   71.292963] [CSI_ERR]sensor initial error when csi open!
[   71.303186] [ccu-err] clk_enable: invalid handle
[   72.254459] incomplete xfer (0x20)
[   72.260655] Error -70 on register write
[   72.268757] [CSI_ERR]chip found is not an ov7670 chip.
[   72.278270] [CSI_ERR]sensor initial error when csi open!
[   73.234377] incomplete xfer (0x20)
[   73.240575] Error -70 on register write
[   73.248675] [CSI_ERR]chip found is not an ov7670 chip.
[   73.258184] [CSI_ERR]sensor initial error when csi open!


Does anyone know how to fix this?
I know that the xfer error suggests something is wrong with the .fex file, but I do not know what. I've tried every possible values I could think of...
The other errors seem a little strange to me as I have no clue what they suggest could be wrong...

I changed the .fex file to:

Code Select Expand


[camera_list_para]
camera_list_para_used = 1
ov7670 = 1
...

[csi0_para]
csi_used = 1
csi_mode = 0
csi_dev_qty = 1
csi_stby_mode = 1
csi_mname = ""
csi_twi_id = 0
csi_twi_addr = 0x42
csi_if = 0
csi_vflip = 0
csi_hflip = 1
csi_iovdd = ""
csi_avdd = ""
csi_dvdd = ""
csi_vol_iovdd = 2800
csi_vol_dvdd = ""
csi_vol_avdd = ""
csi_flash_pol = 1
csi_pck = port:PE00<3><default><default><default>
csi_ck = port:PE01<3><default><default><default>
csi_hsync = port:PE02<3><default><default><default>
csi_vsync = port:PE03<3><default><default><default>
csi_d0 = port:PE04<3><default><default><default>
csi_d1 = port:PE05<3><default><default><default>
csi_d2 = port:PE06<3><default><default><default>
csi_d3 = port:PE07<3><default><default><default>
csi_d4 = port:PE08<3><default><default><default>
csi_d5 = port:PE09<3><default><default><default>
csi_d6 = port:PE10<3><default><default><default>
csi_d7 = port:PE11<3><default><default><default>
csi_reset = port:PH13<1><default><default><0>
csi_power_en = ""
csi_stby = port:PH12<1><default><default><0>
csi_flash = ""
csi_af_en = ""

[csi1_para]
csi_used = 1
csi_mode = 0
csi_dev_qty = 1
csi_stby_mode = 1
csi_mname = ""
csi_twi_id = 1
csi_twi_addr = 0x42
csi_if = 0
csi_vflip = 0
csi_hflip = 1
csi_iovdd = ""
csi_avdd = ""
csi_dvdd = ""
csi_vol_iovdd = 2800
csi_vol_dvdd = ""
csi_vol_avdd = ""
csi_flash_pol = 1
csi_pck = port:PG00<3><default><default><default>
csi_ck = port:PG01<3><default><default><default>
csi_hsync = port:PG02<3><default><default><default>
csi_vsync = port:PG03<3><default><default><default>
csi_d0 = port:PG04<3><default><default><default>
csi_d1 = port:PG05<3><default><default><default>
csi_d2 = port:PG06<3><default><default><default>
csi_d3 = port:PG07<3><default><default><default>
csi_d4 = port:PG08<3><default><default><default>
csi_d5 = port:PG09<3><default><default><default>
csi_d6 = port:PG10<3><default><default><default>
csi_d7 = port:PG11<3><default><default><default>
csi_reset = port:PH13<1><default><default><0>
csi_power_en = ""
csi_stby = port:PH19<1><default><default><0>
csi_flash = ""
csi_af_en = ""


and I added the cameras to the /etc/modules file with the following:

Code Select Expand


ov7670
sun4i_csi0 i2c_addr=0x42 ccm="ov7670"
sun4i_csi1 i2c_addr=0x42 ccm="ov7670"


I also tried I to of different settings, without success.
Any help is appreciated as I am completely stuck at this point

[lorenzo]

Hi Croomch,

in the ov7670 datasheet  it's been reported that the address for write is 0x42 and for reading is the 0x43. Maybe there is something which is not correct with the i2c interface of the sensor.

Can you tell me what happens if you set the address to 0x43?

Thanks
Cheers
Lorenzo

[unlauter]

Hi Croomch,

in the ov7670 datasheet  it's been reported that the address for write is 0x42 and for reading is the 0x43. Maybe there is something which is not correct with the i2c interface of the sensor.

Can you tell me what happens if you set the address to 0x43?

Thanks
Cheers
Lorenzo

This did not work for me, do you have another suggestion please??

To Croomch, this is wrong:
[csi1_para]
csi_used = 1
csi_mode = 0

Because according to:  http://linux-sunxi.org/Fex_Guide

csi_used: 0 to enable; 1 to disable

[JohnS]

I think you've misunderstood the fex - you're quoting an error but see all the examples.

John

[unlauter]

Yea actually I was like  when I saw csi_used: 0 to enable; 1 to disable Because is the opposite in the rest of the FEX, is posible that documentation is wrong?

And Im still cant use my camera