ESP 32 POE ISO rev D ethernet not work

[MicBar]

Hi,

i'm using Olimex ESP32 POE ISO rev D, Arduino IDE 1.8.16 on win 10 PRO
i installed ESP32 Arduino on Card manager of arduino IDE follow this instructions:

https://www.olimex.com/Products/IoT/ESP32/_resources/Arudino-ESP32.txt

i'm using this demo in order to set up ethernet connection between my board and my Pc

https://raw.githubusercontent.com/OLIMEX/ESP32-POE/master/SOFTWARE/ARDUINO/ESP32_PoE_Ethernet_SD_Card_Arduino/ESP32_PoE_Ethernet_SD_Card_Arduino.ino

the code has been modified because my board has not SD card. this is the code:

Code Select Expand

#define ETH_CLK_MODE ETH_CLOCK_GPIO17_OUT
#define ETH_PHY_POWER 12

#include <ETH.h>


static bool eth_connected = false;
#include "FS.h"
#include "SD_MMC.h"

void WiFiEvent(WiFiEvent_t event)
{
  switch (event) {
    case SYSTEM_EVENT_ETH_START:
      Serial.println("ETH Started");
      //set eth hostname here
      ETH.setHostname("esp32-ethernet");
      break;
    case SYSTEM_EVENT_ETH_CONNECTED:
      Serial.println("ETH Connected");
      break;
    case SYSTEM_EVENT_ETH_GOT_IP:
      Serial.print("ETH MAC: ");
      Serial.print(ETH.macAddress());
      Serial.print(", IPv4: ");
      Serial.print(ETH.localIP());
      if (ETH.fullDuplex()) {
        Serial.print(", FULL_DUPLEX");
      }
      Serial.print(", ");
      Serial.print(ETH.linkSpeed());
      Serial.println("Mbps");
      eth_connected = true;
      break;
    case SYSTEM_EVENT_ETH_DISCONNECTED:
      Serial.println("ETH Disconnected");
      eth_connected = false;
      break;
    case SYSTEM_EVENT_ETH_STOP:
      Serial.println("ETH Stopped");
      eth_connected = false;
      break;
    default:
      break;
  }
}

void testClient(const char * host, uint16_t port)
{
  Serial.print("\nconnecting to ");
  Serial.println(host);

  WiFiClient client;
  if (!client.connect(host, port)) {
    Serial.println("connection failed");
    return;
  }
  client.printf("GET / HTTP/1.1\r\nHost: %s\r\n\r\n", host);
  while (client.connected() && !client.available());
  while (client.available()) {
    Serial.write(client.read());
  }

  Serial.println("closing connection\n");
  client.stop();
}


void setup()
{
    Serial.begin(115200);
 
   

    WiFi.onEvent(WiFiEvent);
    ETH.begin();
    pinMode (34, INPUT);  // Button
}



void loop()
{
 
  if (eth_connected) {
    testClient("google.com", 80);
  }
  delay(2000);
}

after flashing arduino code on bord from serial monitor i can see only

"
ETH Started
ETH Connected
"

the board lights yellow-green-red-yellow leds but it cant reach google.com

how can i solve this problem?

i try also to disinstall arduino IDE in order to use these board manager link from:

https://docs.espressif.com/projects/arduino-esp32/en/latest/installing.html

"Currently, the support for new chips (ESP32-S2 and ESP32-C3) is in the development release. Consider installing the development release if you need to test the new supported SoC in beta.

Stable release link:

https://raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_index.json
Development release link:

https://raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_dev_index.json"

but i have the same problem

could someone help me? if you need some other informations please let me know


best regards

[LubOlimex]

It is probably network configuration issue. Check if your network adapter (router, switch, etc, etc) has DHCP enabled.