A13-OLinuXino-WIFI i + A13-LCD7-TS

Started by morn, December 12, 2021, 12:58:40 PM

Previous topic - Next topic
Print
Go Down Pages1
User actions

morn

December 12, 2021, 12:58:40 PM
Hy,
i have the A13-OLinuXino-WIFI now since many many years, its already a rev C board. I used it with Linux and the LCD was working, but i lost interest in SBCs after some time.
I Installed the Linux Debian Bullseye image from your Server. I changed the uboot env via serial console to use lcd instead of vga. The lcd only shows green color and fades to white slowly after kernel started. I cant find information on how to deal with that nor if the new images from the ftp server will work with lcds.
Perhaps someone can give me a hint? It says :
Code Select
video-mode 800x480-18@60 not available, falling back to 1024x768-24@60
LCD not supported on this board :'(

the u boot env:
Code Select
U-Boot SPL 2021.04+olimex-1-20211130.122553 (Nov 30 2021 - 12:26:44 +0000)
DRAM: 512 MiB
CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2
A13 Board no eeprom found!
 PMIC found board is A13-OLinuXino/ A13-OLinuXino WIFI !
Trying to boot from MMC1


U-Boot 2021.04+olimex-1-20211130.122553 (Nov 30 2021 - 12:26:44 +0000) Allwinner Technology

CPU:   Allwinner A13 (SUN5I)
ID:    A13-OLinuXino Rev.AI2C:   ready
DRAM:  512 MiB
MMC:   mmc@1c0f000: 0
Loading Environment from EXT4... OK
video-mode 800x480-18@60 not available, falling back to 1024x768-24@60
LCD not supported on this board
In:    serial
Out:   serial
Err:   serial
Allwinner mUSB OTG (Peripheral)
Net:   eth0: usb_ether
starting USB...
Bus usb@1c14000: USB EHCI 1.00
Bus usb@1c14400: USB OHCI 1.0
scanning bus usb@1c14000 for devices... 3 USB Device(s) found
scanning bus usb@1c14400 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0
=> env print
arch=arm
baudrate=115200
board=a13_olinuxino
board_id=4432
board_name=a13_olinuxino
boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}
boot_efi_binary=load ${devtype} ${devnum}:${distro_bootpart} ${kernel_addr_r} efi/boot/bootarm.efi; if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r};else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi
boot_efi_bootmgr=if fdt addr ${fdt_addr_r}; then bootefi bootmgr ${fdt_addr_r};else bootefi bootmgr;fi
boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}${boot_syslinux_conf}
boot_net_usb_start=usb start
boot_prefixes=/ /boot/
boot_script_dhcp=boot.scr.uimg
boot_scripts=boot.scr.uimg boot.scr
boot_syslinux_conf=extlinux/extlinux.conf
boot_targets=fel mmc0 usb0 pxe dhcp
bootcmd=run distro_bootcmd
bootcmd_dhcp=setenv devtype dhcp; run boot_net_usb_start; if dhcp ${scriptaddr} ${boot_script_dhcp}; then source ${scriptaddr}; fi;setenv efi_fdtfile ${fdtfile}; if test -z "${fdtfile}" -a -n "${soc}"; then setenv efi_fdtfile ${soc}-${board}${boardver}.dtb; fi; setenv efi_old_vci ${bootp_vci};setenv efi_old_arch ${bootp_arch};setenv bootp_vci PXEClient:Arch:00010:UNDI:003000;setenv bootp_arch 0xa;if dhcp ${kernel_addr_r}; then tftpboot ${fdt_addr_r} dtb/${efi_fdtfile};if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r}; else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi;fi;setenv bootp_vci ${efi_old_vci};setenv bootp_arch ${efi_old_arch};setenv efi_fdtfile;setenv efi_old_arch;setenv efi_old_vci;
bootcmd_fel=if test -n ${fel_booted} && test -n ${fel_scriptaddr}; then echo '(FEL boot)'; source ${fel_scriptaddr}; fi
bootcmd_mmc0=devnum=0; run mmc_boot
bootcmd_pxe=run boot_net_usb_start; dhcp; if pxe get; then pxe boot; fi
bootcmd_usb0=devnum=0; run usb_boot
bootdelay=2
bootm_size=0xa000000
console=ttyS0,115200
cpu=armv7
dfu_alt_info_ram=kernel ram 0x42000000 0x1000000;fdt ram 0x43000000 0x100000;ramdisk ram 0x43300000 0x4000000
distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done
efi_dtb_prefixes=/ /dtb/ /dtb/current/
ethaddr=de:ad:be:ef:00:01
fdt_addr_r=0x43000000
fdtcontroladdr=5af530c0
fdtfile=sun5i-a13-olinuxino.dtb
kernel_addr_r=0x42000000
lcd-mode=x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:3,vmode:0
load_efi_dtb=load ${devtype} ${devnum}:${distro_bootpart} ${fdt_addr_r} ${prefix}${efi_fdtfile}
machid=102a
mmc_boot=if mmc dev ${devnum}; then devtype=mmc; run scan_dev_for_boot_part; fi
mmc_bootdev=0
partitions=name=loader1,start=8k,size=32k,uuid=${uuid_gpt_loader1};name=loader2,size=984k,uuid=${uuid_gpt_loader2};name=esp,size=128M,bootable,uuid=${uuid_gpt_esp};name=system,size=-,uuid=${uuid_gpt_system};
preboot=usb start
pxefile_addr_r=0x43200000
ramdisk_addr_r=0x43300000
scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;run scan_dev_for_efi;
scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done; setenv devplist
scan_dev_for_efi=setenv efi_fdtfile ${fdtfile}; if test -z "${fdtfile}" -a -n "${soc}"; then setenv efi_fdtfile ${soc}-${board}${boardver}.dtb; fi; for prefix in ${efi_dtb_prefixes}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${efi_fdtfile}; then run load_efi_dtb; fi;done;run boot_efi_bootmgr;if test -e ${devtype} ${devnum}:${distro_bootpart} efi/boot/bootarm.efi; then echo Found EFI removable media binary efi/boot/bootarm.efi; run boot_efi_binary; echo EFI LOAD FAILED: continuing...; fi; setenv efi_fdtfile
scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${boot_syslinux_conf}; then echo Found ${prefix}${boot_syslinux_conf}; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi
scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done
scriptaddr=0x43100000
serial#=162541d8098175cf
soc=sunxi
stderr=serial,lcd
stdin=serial,usbkbd
stdout=serial,lcd
usb_boot=usb start; if usb dev ${devnum}; then devtype=usb; run scan_dev_for_boot_part; fi
usbnet_devaddr=de:ad:be:ef:00:01
uuid_gpt_esp=c12a7328-f81f-11d2-ba4b-00a0c93ec93b
uuid_gpt_system=69dad710-2ce4-4e3c-b16c-21a1d49abed3
vendor=olimex
video-mode=sunxi:800x480-18@60,monitor=lcd

Environment size: 4684/131068 bytes
=>
arch=arm
baudrate=115200
board=a13_olinuxino
board_id=4432
board_name=a13_olinuxino
boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}
boot_efi_binary=load ${devtype} ${devnum}:${distro_bootpart} ${kernel_addr_r} efi/boot/bootarm.efi; if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r};else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi
boot_efi_bootmgr=if fdt addr ${fdt_addr_r}; then bootefi bootmgr ${fdt_addr_r};else bootefi bootmgr;fi
boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}${boot_syslinux_conf}
boot_net_usb_start=usb start
boot_prefixes=/ /boot/
boot_script_dhcp=boot.scr.uimg
boot_scripts=boot.scr.uimg boot.scr
boot_syslinux_conf=extlinux/extlinux.conf
boot_targets=fel mmc0 usb0 pxe dhcp
bootcmd=run distro_bootcmd
bootcmd_dhcp=setenv devtype dhcp; run boot_net_usb_start; if dhcp ${scriptaddr} ${boot_script_dhcp}; then source ${scriptaddr}; fi;setenv efi_fdtfile ${fdtfile}; if test -z "${fdtfile}" -a -n "${soc}"; then setenv efi_fdtfile ${soc}-${board}${boardver}.dtb; fi; setenv efi_old_vci ${bootp_vci};setenv efi_old_arch ${bootp_arch};setenv bootp_vci PXEClient:Arch:00010:UNDI:003000;setenv bootp_arch 0xa;if dhcp ${kernel_addr_r}; then tftpboot ${fdt_addr_r} dtb/${efi_fdtfile};if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r}; else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi;fi;setenv bootp_vci ${efi_old_vci};setenv bootp_arch ${efi_old_arch};setenv efi_fdtfile;setenv efi_old_arch;setenv efi_old_vci;
bootcmd_fel=if test -n ${fel_booted} && test -n ${fel_scriptaddr}; then echo '(FEL boot)'; source ${fel_scriptaddr}; fi
bootcmd_mmc0=devnum=0; run mmc_boot
bootcmd_pxe=run boot_net_usb_start; dhcp; if pxe get; then pxe boot; fi
bootcmd_usb0=devnum=0; run usb_boot
bootdelay=2
bootm_size=0xa000000
console=ttyS0,115200
cpu=armv7
dfu_alt_info_ram=kernel ram 0x42000000 0x1000000;fdt ram 0x43000000 0x100000;ramdisk ram 0x43300000 0x4000000
distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done
efi_dtb_prefixes=/ /dtb/ /dtb/current/
ethaddr=de:ad:be:ef:00:01
fdt_addr_r=0x43000000
fdtcontroladdr=5af530c0
fdtfile=sun5i-a13-olinuxino.dtb
kernel_addr_r=0x42000000
lcd-mode=x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:3,vmode:0
load_efi_dtb=load ${devtype} ${devnum}:${distro_bootpart} ${fdt_addr_r} ${prefix}${efi_fdtfile}
machid=102a
mmc_boot=if mmc dev ${devnum}; then devtype=mmc; run scan_dev_for_boot_part; fi
mmc_bootdev=0
partitions=name=loader1,start=8k,size=32k,uuid=${uuid_gpt_loader1};name=loader2,size=984k,uuid=${uuid_gpt_loader2};name=esp,size=128M,bootable,uuid=${uuid_gpt_esp};name=system,size=-,uuid=${uuid_gpt_system};
preboot=usb start
pxefile_addr_r=0x43200000
ramdisk_addr_r=0x43300000
scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;run scan_dev_for_efi;
scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done; setenv devplist
scan_dev_for_efi=setenv efi_fdtfile ${fdtfile}; if test -z "${fdtfile}" -a -n "${soc}"; then setenv efi_fdtfile ${soc}-${board}${boardver}.dtb; fi; for prefix in ${efi_dtb_prefixes}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${efi_fdtfile}; then run load_efi_dtb; fi;done;run boot_efi_bootmgr;if test -e ${devtype} ${devnum}:${distro_bootpart} efi/boot/bootarm.efi; then echo Found EFI removable media binary efi/boot/bootarm.efi; run boot_efi_binary; echo EFI LOAD FAILED: continuing...; fi; setenv efi_fdtfile
scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${boot_syslinux_conf}; then echo Found ${prefix}${boot_syslinux_conf}; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi
scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done
scriptaddr=0x43100000
serial#=162541d8098175cf
soc=sunxi
stderr=serial,lcd
stdin=serial,usbkbd
stdout=serial,lcd
usb_boot=usb start; if usb dev ${devnum}; then devtype=usb; run scan_dev_for_boot_part; fi
usbnet_devaddr=de:ad:be:ef:00:01
uuid_gpt_esp=c12a7328-f81f-11d2-ba4b-00a0c93ec93b
uuid_gpt_system=69dad710-2ce4-4e3c-b16c-21a1d49abed3
vendor=olimex
video-mode=sunxi:800x480-18@60,monitor=lcd

Environment size: 4684/131068 bytes
Here is the head of the bootlog:

Code Select
-Boot SPL 2021.04+olimex-1-20211130.122553 (Nov 30 2021 - 12:26:44 +0000)
DRAM: 512 MiB
CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2
A13 Board no eeprom found!
 PMIC found board is A13-OLinuXino/ A13-OLinuXino WIFI !
Trying to boot from MMC1


U-Boot 2021.04+olimex-1-20211130.122553 (Nov 30 2021 - 12:26:44 +0000) Allwinner Technology

CPU:   Allwinner A13 (SUN5I)
ID:    A13-OLinuXino Rev.AI2C:   ready
DRAM:  512 MiB
MMC:   mmc@1c0f000: 0
Loading Environment from EXT4... OK
video-mode 800x480-18@60 not available, falling back to 1024x768-24@60
LCD not supported on this board
In:    serial
Out:   serial
Err:   serial
Allwinner mUSB OTG (Peripheral)
Net:   eth0: usb_ether
starting USB...
Bus usb@1c14000: USB EHCI 1.00
Bus usb@1c14400: USB OHCI 1.0
scanning bus usb@1c14000 for devices... 3 USB Device(s) found
scanning bus usb@1c14400 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
2022 bytes read in 3 ms (658.2 KiB/s)
## Executing script at 43100000
Checking for /uEnv.txt...
Checking for /boot/uEnv.txt...
400 bytes read in 2 ms (195.3 KiB/s)
Loaded environment from /boot/uEnv.txt
Loading FIT image...
15792543 bytes read in 1250 ms (12 MiB/s)
## Loading kernel from FIT Image at 58000000 ...
   Using 'config-4432' configuration
   Trying 'kernel-1' kernel subimage
     Description:  Linux kernel 5.10.60-olimex
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0x580000d0
     Data Size:    6518984 Bytes = 6.2 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: 0x40080000
     Entry Point:  0x40080000
     Hash algo:    crc32
     Hash value:   c12c1fa2
     Hash algo:    sha1
     Hash value:   772e08be6d8dc234916f0aa43c10a4dc2226bcc4
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading ramdisk from FIT Image at 58000000 ...
   Using 'config-4432' configuration
   Trying 'ramdisk-1' ramdisk subimage
     Description:  Ramdisk for kernel 5.10.60-olimex
     Type:         RAMDisk Image
     Compression:  Unknown Compression
     Data Start:   0x58637acc
     Data Size:    9203342 Bytes = 8.8 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: 0x4fe00000
     Entry Point:  0x4fe00000
     Hash algo:    crc32
     Hash value:   31703dd5
     Hash algo:    sha1
     Hash value:   d0c8bd9172d33b0993d8598e38e0bfd526d4152f
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Loading ramdisk from 0x58637acc to 0x4fe00000
WARNING: 'compression' nodes for ramdisks are deprecated, please fix your .its file!
## Loading fdt from FIT Image at 58000000 ...
   Using 'config-4432' configuration
   Trying 'fdt-1' fdt subimage
     Description:  unavailable
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x58efea48
     Data Size:    23020 Bytes = 22.5 KiB
     Architecture: ARM
     Load Address: 0x4fa00000
     Hash algo:    crc32
     Hash value:   fe1e1efe
     Hash algo:    sha1
     Hash value:   0d226f727ca4493b9350ba2eb9ea4f28667dfaec
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Loading fdt from 0x58efea48 to 0x4fa00000
   Booting using the fdt blob at 0x4fa00000
   Loading Kernel Image
   Loading Ramdisk to 49739000, end 49fffe8e ... OK
   Loading Device Tree to 49730000, end 497389eb ... OK
Using machid 0x102a from environment

Starting kernel ...

[    0.050155] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.876898] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO
Loading, please wait...
Starting version 247.3-6
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.36.1
[/sbin/fsck.ext4 (1) -- /dev/mmcblk0p1] fsck.ext4 -a -C0 /dev/mmcblk0p1
/dev/mmcblk0p1: clean, 136548/461216 files, 688887/1888256 blocks
done.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.

Welcome to ␛[1mDebian GNU/Linux 11 (bullseye)␛[0m![/code

LubOlimex

#1
December 13, 2021, 03:59:34 PM
What is the LCD exactly? Did you check the Olimage document here:

https://github.com/OLIMEX/OLINUXINO/blob/master/DOCUMENTS/OLIMAGE/Olimage-guide.pdf
Technical support and documentation manager at Olimex
Print
Go Up Pages1
User actions