≡
Difference between revisions of "RT5350F-OLinuXino"
m (→Building OpenWRT) |
m (→Building OpenWRT) |
||
Line 35: | Line 35: | ||
raspi_read: from:30000 len:1000 | raspi_read: from:30000 len:1000 | ||
.*** Warning - bad CRC, using default environment | .*** Warning - bad CRC, using default environment | ||
− | + | ||
============================================================= | ============================================================= | ||
RT5350F-OLinuXino UBoot Version: 4.0.0.0 | RT5350F-OLinuXino UBoot Version: 4.0.0.0 | ||
Line 62: | Line 62: | ||
7: Load Boot Loader code then write to Flash via Serial. | 7: Load Boot Loader code then write to Flash via Serial. | ||
9: Load Boot Loader code then write to Flash via TFTP. | 9: Load Boot Loader code then write to Flash via TFTP. | ||
+ | |||
+ | Press 2, then y and enter some values for ip, server ip and filename: | ||
+ | |||
+ | You choosed 2 | ||
+ | |||
+ | |||
+ | 2: System Load Linux Kernel then write to Flash via TFTP. | ||
+ | Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) | ||
+ | Please Input new ones /or Ctrl-C to discard | ||
+ | Input device IP (10.10.10.123) ==:10.10.10.123 | ||
+ | Input server IP (10.10.10.3) ==:10.10.10.3 | ||
+ | Input Linux Kernel filename () ==:file.bin | ||
+ | |||
+ | Then your new system will boot. |
Revision as of 23:58, 22 April 2015
RT5350F-OLinuXino
Overview
Building OpenWRT
Make a directory:
# mkdir some_dir # cd some_dir
Download sources:
# git clone https://github.com/OLIMEX/openwrt -b rt5350f
Go into openwrt directory:
# cd openwrt
You can use our config:
# make
or if you want to change something:
# make menuconfig # make
After some time build will finish. The image is found under:
build_dir/target-mipsel_24kec+dsp_uClibc-0.9.33.2/linux-ramips_rt305x/openwrt-ramips-rt305x-olinuxino-rt5350f-squashfs-sysupgrade.bin
Place that file on some tftp server. Reboot the board and you'll see:
U-Boot 1.1.3 (Apr 20 2015 - 13:25:55)
Board: RT5350F-OLinuXino DRAM: 32 MB relocate_code Pointer at: 81fb4000 spi_wait_nsec: 42 spi device id: 1c 30 17 1c 30 (30171c30) find flash: EN25Q64 raspi_read: from:30000 len:1000 .*** Warning - bad CRC, using default environment ============================================================= RT5350F-OLinuXino UBoot Version: 4.0.0.0 -------------------------------------------------------------- ASIC 5350_MP (Port5<->None) DRAM_CONF_FROM: Boot-Strapping DRAM_TYPE: SDRAM DRAM_SIZE: 256 Mbits DRAM_WIDTH: 16 bits DRAM_TOTAL_WIDTH: 16 bits TOTAL_MEMORY_SIZE: 32 MBytes Flash component: SPI Flash Date:Apr 20 2015 Time:13:25:55 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 360 MHZ #### estimate memory size =32 Mbytes
Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP.
Press 2, then y and enter some values for ip, server ip and filename:
You choosed 2 2: System Load Linux Kernel then write to Flash via TFTP. Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Please Input new ones /or Ctrl-C to discard Input device IP (10.10.10.123) ==:10.10.10.123 Input server IP (10.10.10.3) ==:10.10.10.3 Input Linux Kernel filename () ==:file.bin
Then your new system will boot.