RK3188-SOM

Overview

This one is little beast comparing to A20 it have 4x Cortex-A9 vs 2x Cortex-A7 and runs on 1.6GHz vs. 1GHz so RK3188 makes total 16000 DMPIS vs. 3800 DMIPS for A20 (4.2 times faster) and vs. 965 DMIPS for RaspberryPi (16.6 times faster).

On the SOM there is:

• RK3188 running at 1.6Ghz
• 1GB DDR3 memory
• Power Managment Unit IC
• Optional 4GB NAND Flash
• Micro SD-card to boot Llinux or Android
• Three buttons
• Four status LEDs (one for power and three programmable)
• Debug UART console
• Five GPIO connectors 2×20 pins 0.05″ step

Linux

Booting from SD-card

Writing Rockchip loader

dd if=loader.img of=/dev/sde conv=sync,fsync
dd if=parameter of=/dev/sde conv=sync,fsync seek=$((0x2000))
dd if=boot.img of=/dev/sde conv=sync,fsync seek=$((0x2000+0x2000))

Building kernel

./mkbootimg --kernel RK3188-SOM/arch/arm/boot/Image --ramdisk initrd.img -o boot.img

Creating root filesystem

Debian Wheezy

---

In this post we will explain how you can create your own Debian rootfs with pre-installed packages of your choice, which to allow tiny Linux images to be created. All steps below should work on any Debian host (Debian/Ubuntu etc) and are verified with Ubuntu 12.04LTS. First of all you need to install the support packages on your pc:

• Install needed packages:

sudo apt-get install qemu-user-static debootstrap binfmt-support

• Define some variables:

targetdir=rootfs
distro=wheezy

• Build first stage:

mkdir $targetdir
sudo debootstrap --arch=armhf --foreign $distro $targetdir

• Copy needed files from host to the target:

sudo cp /usr/bin/qemu-arm-static $targetdir/usr/bin/
sudo cp /etc/resolv.conf $targetdir/etc

If everything is right we now have a minimal Debian Rootfs.

• Login into the new filesystem:

sudo chroot $targetdir 

• Inside the chroot we need to set up the environment again

distro=wheezy
export LANG=C 

• Now we are setup the second stage of debootstrap needs to run install the packages downloaded earlier

/debootstrap/debootstrap --second-stage

• Once the package installation has finished, setup some support files and apt configuration.

cat <<EOT > /etc/apt/sources.list
deb http://ftp.uk.debian.org/debian $distro main contrib non-free
deb-src http://ftp.uk.debian.org/debian $distro main contrib non-free
deb http://ftp.uk.debian.org/debian $distro-updates main contrib non-free
deb-src http://ftp.uk.debian.org/debian $distro-updates main contrib non-free
deb http://security.debian.org/debian-security $distro/updates main contrib non-free
deb-src http://security.debian.org/debian-security $distro/updates main contrib non-free
EOT 

• Update Debian package database:

apt-get update 

• set up locales dpkg scripts tend to complain otherwise, note in jessie you will also need to install the dialog package as well.

apt-get install locales dialog sudo
dpkg-reconfigure locales
chmod u+s /usr/bin/sudo 

• Install some useful packages inside the chroot

apt-get install openssh-server ntpdate 

• Set a root password so you can login

passwd 

• Build a basic network interface file so that the board will DHCP on eth0

echo <<EOT >> /etc/network/interfaces
allow-hotplug eth0
iface eth0 inet static
    address 192.168.1.254
    netmask 255.255.255.248
    gateway 192.168.1.1
EOT 

Note: Your board will be accessible over SSH on IP address defined above!

• Set the hostname

echo nameme > /etc/hostname 

• Enable the serial console, Debian sysvinit way

echo T0:2345:respawn:/sbin/getty -L ttyFIQ0 115200 vt100 >> /etc/inittab

This way you'll get login prompt at startup. By default you cannot login as root. To do this you should make another user, add him to the sudo group, login at startup and then login as root. To skip all this replace the line above with:

echo T0:2345:respawn:/sbin/getty -L ttyFIQ0 -a root 115200 vt100 >> /etc/inittab 

• We are done inside the chroot, so quit the chroot shell

exit

• Tidy up the support files

sudo rm $targetdir/etc/resolv.conf
sudo rm $targetdir/usr/bin/qemu-arm-static

Installing X

---

You cannot run X as root(actually it's possible, but it's bad practice), so you have to add new user to run X.

• Edit default useradd settings

vi /etc/default/useradd

Modify SHELL variable:

SHELL=/bin/bash

• Add new user

useradd myuser

• Add the user to the sudo group

adduser myuser sudo

• Make home folder

mkdir /home/myuser
chown -R myuser:myuser /home/myuser

• Install xfce4 and lightdm

apt-get update
apt-get install lightdm xfce4