Difference between revisions of "How to use 15 inch touchscreens"
| Line 3: | Line 3: | ||
This guide is tested with the LCD-15.6TS (with ETT5003U controller), distributed by Olimex LTD. The setup included LCD-OLinuXino-15.6-FHD and A20-OLinuXino-MICRO. | This guide is tested with the LCD-15.6TS (with ETT5003U controller), distributed by Olimex LTD. The setup included LCD-OLinuXino-15.6-FHD and A20-OLinuXino-MICRO. | ||
| − | Important: for the hardware connection you would need to provide 5V and 12V to the touchscreen display. A free USB port is also required. The powering to the touchscreen is deliver through a standard 4-pin molex connector. | + | Important: for the hardware connection you would need to provide 5V and 12V to the touchscreen display. A free USB port is also required. The powering to the touchscreen is deliver through a standard 4-pin molex connector. |
After all hardware connections are established to get the touchscreen working under the official Linux image do the following: | After all hardware connections are established to get the touchscreen working under the official Linux image do the following: | ||
| − | 1. Make sure the USB connection between the display and the board is established before powering the board. If it was connected already reboot the board. | + | '''1.''' Make sure the USB connection between the display and the board is established before powering the board. If it was connected already reboot the board. |
| − | 2. Identify the event number of the USB connection of the touschreen. You might plug-unplug the USB connection of the touchscreen to get the proper event number in the console (or use command dmesg | grep ETwo). | + | '''2.''' Identify the event number of the USB connection of the touschreen. You might plug-unplug the USB connection of the touchscreen to get the proper event number in the console (or use command dmesg | grep ETwo). |
| − | 3. Create a new 20-ts.conf file or add a new section in the 20-ts. | + | '''3.''' Create a new 20-ts.conf file or add a new section in the 20-ts.conf file (remember to replace the USB event number with the number you got in point 1, we have used event2 as example) |
| − | The file location is: | + | The file location is: /usr/share/X11/xorg.conf.d/20-ts.conf |
The file should contain the following: | The file should contain the following: | ||
| − | + | Section "InputClass" | |
| − | + | Identifier "ETwo TouchScreen" | |
| − | + | MatchDevicePath "/dev/input/event2" | |
| − | + | MatchProduct "ETwoTouch Corp. ETwo TouchScreen" | |
| − | + | Driver "tslib" | |
| − | + | Option "ScreenNumber" "0" | |
| − | + | Option "Rotate" "NONE" | |
| − | + | Option "Width" "1920" | |
| − | + | Option "Height" "1080" | |
| − | + | Option "SendCoreEvents" "yes" | |
| − | + | Option "Type" "touchscreen" | |
| − | + | EndSection | |
'''Remember to replace the event2 number with the number you got in point 1. The configuration is suitable for the FullHD 15.6 inch display. If you are using the 1366x768 (HD-ready) display replace the driver option defaults with "Width" "1366" and "Height" "768".''' | '''Remember to replace the event2 number with the number you got in point 1. The configuration is suitable for the FullHD 15.6 inch display. If you are using the 1366x768 (HD-ready) display replace the driver option defaults with "Width" "1366" and "Height" "768".''' | ||
| − | 4. Create a new environment file or edit the environment file (again we have used event2 as our USB event, remember to replace it with the number of event you get in point 1.) | + | '''4.''' Create a new environment file or edit the environment file (again we have used event2 as our USB event, remember to replace it with the number of event you get in point 1.) |
| − | The file location is: | + | The file location is: /etc/environment |
| − | + | TSLIB_TSEVENTTYPE=raw | |
| − | + | TSLIB_CONSOLEDEVICE=none | |
| − | + | TSLIB_FBDEVICE=/dev/fb0 | |
| − | + | TSLIB_TSDEVICE=/dev/input/event2 | |
| − | + | TSLIB_CALIBFILE=/etc/pointercal | |
| − | + | TSLIB_CONFFILE=/usr/etc/ts.conf | |
| − | + | TSLIB_PLUGINDIR=/usr/lib/ts | |
| − | + | Again remember to replace the event2 number with the number you got in point 1. | |
| − | 5. | + | '''5.''' Calibrate the display like root user |
| − | + | ts_calibrate | |
| − | + | '''6.''' Add the following 2 lines at the end of /root/.bashrc file: | |
| − | + | service slim stop | |
| + | su - olimex -c startx & | ||
| − | + | '''7.''' Reboot the board | |
| − | + | reboot | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
[[Main_Page]] | [[Main_Page]] | ||
Revision as of 21:21, 25 May 2015
Instructions on the usage of the 15.6 inch SAW touchscreen (LCD-15.6TS) under Debian.
This guide is tested with the LCD-15.6TS (with ETT5003U controller), distributed by Olimex LTD. The setup included LCD-OLinuXino-15.6-FHD and A20-OLinuXino-MICRO.
Important: for the hardware connection you would need to provide 5V and 12V to the touchscreen display. A free USB port is also required. The powering to the touchscreen is deliver through a standard 4-pin molex connector.
After all hardware connections are established to get the touchscreen working under the official Linux image do the following:
1. Make sure the USB connection between the display and the board is established before powering the board. If it was connected already reboot the board.
2. Identify the event number of the USB connection of the touschreen. You might plug-unplug the USB connection of the touchscreen to get the proper event number in the console (or use command dmesg | grep ETwo).
3. Create a new 20-ts.conf file or add a new section in the 20-ts.conf file (remember to replace the USB event number with the number you got in point 1, we have used event2 as example)
The file location is: /usr/share/X11/xorg.conf.d/20-ts.conf
The file should contain the following:
Section "InputClass" Identifier "ETwo TouchScreen" MatchDevicePath "/dev/input/event2" MatchProduct "ETwoTouch Corp. ETwo TouchScreen" Driver "tslib" Option "ScreenNumber" "0" Option "Rotate" "NONE" Option "Width" "1920" Option "Height" "1080" Option "SendCoreEvents" "yes" Option "Type" "touchscreen" EndSection
Remember to replace the event2 number with the number you got in point 1. The configuration is suitable for the FullHD 15.6 inch display. If you are using the 1366x768 (HD-ready) display replace the driver option defaults with "Width" "1366" and "Height" "768".
4. Create a new environment file or edit the environment file (again we have used event2 as our USB event, remember to replace it with the number of event you get in point 1.)
The file location is: /etc/environment
TSLIB_TSEVENTTYPE=raw TSLIB_CONSOLEDEVICE=none TSLIB_FBDEVICE=/dev/fb0 TSLIB_TSDEVICE=/dev/input/event2 TSLIB_CALIBFILE=/etc/pointercal TSLIB_CONFFILE=/usr/etc/ts.conf TSLIB_PLUGINDIR=/usr/lib/ts
Again remember to replace the event2 number with the number you got in point 1.
5. Calibrate the display like root user
ts_calibrate
6. Add the following 2 lines at the end of /root/.bashrc file:
service slim stop su - olimex -c startx &
7. Reboot the board
reboot
- Content is available under GNU Free Documentation License 1.3 or later unless otherwise noted.
